New Firmware available OTA  v 1.00.16 (27 June 08)
Click Menu -> Installation ->Software Update -> Manual Update
Set as follows:-
Satellite: Hotbird 13east
Frequency: 12.476
Polarisation: Horizontal
Symbol Rate: 27500
FEC: 3/4
Average upload time = 15 mins.

Please Note: The OTA upload may take some of you over two (2) hours to complete.
The main reason the upload may take so long for some, is simply
because your dish is not properly aligned on the satellite,
and the signal quality is fluctuating, and may even drop below
the signal threshold. To prevent this problem, simply tweek your dish before you start.

HDCI 2000 Channel List

==================================================

This list is mainly aimed at Diablo / Dragon Cam users

New in this update:

(DC_5.0) First released  12 September 08

Conax channels now added to Thor + ITV HD added to Astra 2
Many new channels added including ORF HD on Astra 1
and many channels removed, to generate space for the Conax channels.

If you have any suggestions, on how to improve
this channel list, then please, feel free to post
your suggestions at: http://sataid.net/forum

Please Note:
I do not mind anyone using my list, or even distributing it on other upload sites or forums, but I would expect the people who do post my channel list elsewhere, to at least have the decency to leave the file intact, and not remove or edit the readme file, or is that realy to much to expect.

Download Logon Details Here

 

 

HDCI 2000 Channel Editors

Please Note:
To use the channel editor, you must turn off your Humax HDCI-2000
by the Off/On switch located on the back of the receiver, otherwise
all you will get is a connection time out Error message.
Transfering the channel list from your receiver, to your computer,
can take quite a long time, so please, be patient as it can take upto 10 - 17 secs per 1%

 

HDCI 2000 Firmware and Firmware Loader

 

Humax Official Downloads for the HDCI 2000

 

Click Here for additional Help

Humax HDCI 2000 Error messages.

When you have any problem during downloading,you may see one of the following error code at the front panel display:

Error Code            Description of Error           Remedy

E-HC/bC Incorrect header block(CRC-16) The software seems damaged while you receive from web site or e-mail.
Please receive the software again and try to download

E-dC Incorrect data block(CRC-16) The software seems damaged while you receive from web site or e-mail.
Please receive the software again and try to download

E-Hn/bF Invalid HDF version This error can be occured when you attempt to download Non-Superset STB software to Superset or Vice-Versa.
Please check the STB model and the software

E-Id Invalid system ID This error can be occured when you attempt to download F1 software to F1-CI.
Please check the STB model and the software

E-AC Incorrect application CRC-32 Download latest version of application sw. If it doesn't make it, the flash memory may be thought to be defected

E-ut UART RX/TX time out There is communication problem between source and target

1) Check whether the S/W is compressed or not and Check whether you use the proper download tool for the software
2) Reduce the download speed and try to download again
3) STB main power Off/On and try to download again
4) Reset the PC and try to download again

E-Ad Invalid address Humax made the hdf file with wrong address.
Please notify this error to us and wait until we release the proper software.

E-Ao Invalid offset address for upload(Odd offset) There was a mistake when we made hdf file from binary file.
Please let us know immediately and wait new release version

E-Ft Flash program time out The flash memory in STB seems damaged.
Please try to download one more time. If you fail agian,send us back to replace the flash memory device

E-It/Et EEPROM program time out The EEPROM in STB seems damaged.
Please try to download one more time. If you fail again,replace the EEPROM device

E-FE Fail compare after flash write Flash memory is damaged.
Return the main board(CPU Board)

E-HF Invalid HDF Format It means that the file you try to download is not a valid HDF format. The file could be damaged in which case you should try downloading it from the Humax web site again. Also please check the file extension is HDF. Also make sure you are using the correct download tool - Wdn4oak+. It can be also occurred when there is some problem on cable, data of PC and loader.

E-Fn Invalid flash device Flash memory is defected
Need to change the flash memory so Please return the Main Board

E-AS Incorrect application size Check the software version and STB hardware specification